ClaasEco Microbubble (MB) and Ultrafine Bubble (UFB) award winningpatented generators efficiently delivers dissolved oxygen to plant roots by saturating the water with ambient oxygen (Ultra-Yield) or saturated oxygen (Ultra-Yield +).
What is it:
The Ultra-Yield is a system developed with the latest aeration technology in the world to increase the dissolved oxygen (DO) in water at rates and speeds never been seen before. Our advanced technologies, that includes the MB/UFB generators, aerates water at a rate between 8 000 micro-bubbles to +1 000 000 ultra-fine bubbles per 1ml of water, a first in the water treatment industry.
This means that it is possible now to dissolve oxygen or any gas 10 to 1 000 times more efficiently than 1mm bubble generators.
When adding oxygen into the Micro and Ultrafine bubble it will further increase the DO (Dissolved Oxygen) in irrigation and aquaculture water.
What makes the technology so amazing is that with a 90% oxygen percentage level, which can be determined as 38 mg/L, you can expect a 427% saturation level subject to your water temperature and viscosity. This is very good news for plants indeed.
See table below for %Oxygen, mg/L, % Saturation ratio:
how it works in aquaculture:
Over 50% of the fish and shellfish consumed by humans are produced through aquaculture, also known as fish farming. As fish farmers aim to produce more fish to keep up with global demand, they run into severe problems with a lack of dissolved oxygen (DO) in the water. Fish and shellfish need a specific minimum amount oxygen to breathe. When fish populations are tightly packed, a shortage of DO is inevitable because the fish and shellfish consume more oxygen from the water, than what is naturally available.
Additionally, waste by-products accumulate on the bottom of the fish farm, damaging or eliminating bottom-dwelling plants and animals required for a healthy eco system. ClaasEco Micro and Ultrafine bubble gas injection technology can alleviate these problems by rapidly elevating and maintaining higher levels of DO levels in the aquaculture environment, effectively oxygenating sea, dam and lake floors due to the Ultrafine bubble’s lack of buoyancy.
how it works in horticulture and hydroponics:
ClaasEco Micro and Ultrafine bubble gas injection technology enables the cost–effective use of oxygen to improve water quality to help promote nutrient uptake, increase plant health and suppress root disease. It is our ability to convert bulk gases like oxygen into Ultrafine bubbles that gives our technology a unique advantage over traditional forms of aeration and oxygenation.
For example, Ultra Fine Bubbles enable us to deliver high levels of oxygen directly to the root surface where the oxygen plays a critical role in facilitating nutrient absorption and maintaining optimal root- and plant health. Around the world it is consistently demonstrated over a wide variety of crops using multiple cultivation methods that dissolved oxygen delivered through Ultrafine bubbles can significantly improve plant health and resistance to environmental and pathogen stress. Supercharging a plant’s metabolism with usable oxygen can increase yield while reducing the crop-turn cycle.
ultra-yield n series:
The three models with 1, 3, and 5 sets of Dual-chamber/Dual-vortex/High-speed Rotation System (DDHRS) nozzles enable us to apply the Ultra-YIELD solutions in any water body, where it is required to use a pump OUTSIDE of the water and where the application ask for the highest possible gas transfer in the water body. What makes the 3N and 5N very unique, is the fact that we can apply 3 times or 5 times more MB/UFB air bubbles in the water with the same amount of water flow. This is the only patented equipment in the world that is capable of doingso.
The equipment requires a mereNominal power P2 of 1.5 kW, Rated speed of 2900 1/min,Rated voltage of 3~/230 V / 400 V / 50 Hz,35m3/h pump to operate.
Note for the Farmer: Because the equipment produce air bubbles that can stay in the water for months, and at much larger volumes, it is not necessary to use every litre of water to increase the DO of the water body.We can do it 30 times faster than normal aeration techniques and achieve a gas transfer capability of 90% compared to 2% normally available. How do we do it? If a venturi make a bubble and we compare it to the size of Earth, the our bubbles range between the size of a school bus
No. of nozzles: 1 Weight: 5kg Material: Stainless Steel 316 Size (cm): 22 x 15 Gas Transfer Capability (%): 90%
The two models 350S and 400S, are are units each with the same Dual-chamber/Dual-vortex/High-speed Rotation System (DDHRS) nozzle, but manufactured out of two different grades of stainless steel (304 and 316). They enable us to apply the Ultra-YIELD solutions in any water body, where it is required to use a pump INSIDE the water body. What makes the S series unique, is the fact that we can apply the solution in very harsh conditions such as sea water. Combined with solar power, they can run 24/7 non-stop in remote areas.
The equipment requires a mereNominal power of 370W,200V/50Hz/60HZ / Single Phase, 18m3/h Submersiblepump to operate.
Note for the Farmer: Because the equipment produce air bubbles that can stay in the water for months, and at much larger volumes, it is not necessary to use every litre of water to increase the DO of the water body. We can do it 30 times faster than normal aeration techniques and achieve a gas transfer capability of 90% compared to 2% normally available.For harsh conditions, we recommend our titaniumimpeller type submersible pump. How do we do it? If a venturi make a bubble and we compare it to the size of Earth, then our bubbles range between the size of a school bus and honey bee.
No of nozzles: 1 Output (W):370 Weight: 14.5kg Phase/Voltage (V): Single, 200 Nozzle Material: Stainless Steel 316 Impeller Material: Titanium Size (cm):35×25 Gas Transfer Capability (%):90%